.:                     :,                                          
,:::::::: ::`      :::                   :::                                          
,:::::::: ::`      :::                   :::                                          
.,,:::,,, ::`.:,   ... .. .:,     .:. ..`... ..`   ..   .:,    .. ::  .::,     .:,`   
   ,::    :::::::  ::, :::::::  `:::::::.,:: :::  ::: .::::::  ::::: ::::::  .::::::  
   ,::    :::::::: ::, :::::::: ::::::::.,:: :::  ::: :::,:::, ::::: ::::::, :::::::: 
   ,::    :::  ::: ::, :::  :::`::.  :::.,::  ::,`::`:::   ::: :::  `::,`   :::   ::: 
   ,::    ::.  ::: ::, ::`  :::.::    ::.,::  :::::: ::::::::: ::`   :::::: ::::::::: 
   ,::    ::.  ::: ::, ::`  :::.::    ::.,::  .::::: ::::::::: ::`    ::::::::::::::: 
   ,::    ::.  ::: ::, ::`  ::: ::: `:::.,::   ::::  :::`  ,,, ::`  .::  :::.::.  ,,, 
   ,::    ::.  ::: ::, ::`  ::: ::::::::.,::   ::::   :::::::` ::`   ::::::: :::::::. 
   ,::    ::.  ::: ::, ::`  :::  :::::::`,::    ::.    :::::`  ::`   ::::::   :::::.  
                                ::,  ,::                               ``             
                                ::::::::                                              
                                 ::::::                                               
                                  `,,`


http://www.thingiverse.com/thing:1335535
CowTech Ciclop 3D Scanner by CowTech is licensed under the Creative Commons - Attribution - Share Alike license.
http://creativecommons.org/licenses/by-sa/3.0/

# Summary

Finalized Parts! Feel free to download, as these won't be changing anymore. 

CowTech Ciclop, designed from the BQ Ciclop, but redesigned to use half the print time, 2/3 of the filament, and a tiny print bed area of only 115mm x 110mm x 65mm (4.5 x 4.3 x 2.6in) so the parts can be printed on nearly any printer. Funded on Kickstarter, raising $183,800 from 1400 backers. Kits now available for pre-order at www.cowtechengineering.com

You will need two each of the laser core, laser holder, and pattern holder. 
PLA or ABS are both fine. 

Laser Cut Parts. All sizes in inches. 
1x Top T .220
1x Bottom T .220
1x Faceplate .220
1x Turntable .220/.236
1x Frosted .062/.125 (if you don't have frosted acrylic, lightly raster the surface)
1x Pattern .062
3x Wire Holder .220
2x Laser Arm .220

Some of the previews look funky, but they donwload accurately. 




# Print Settings

Printer Brand: RepRap
Printer: Prusa i3
Rafts: No
Supports: Yes
Resolution: 0.2mm
Infill: 10%

Notes: 
Camera Base : Support everywhere, no platform adhesion needed

Motor base : Support everywhere, no platform adhesion needed

Camera Holder: No support, no platform adhesion. 

Backplate : Support everywhere, no platform adhesion needed (print standing up with flat side down).

Laser Holder : Support everywhere, no platform adhesion needed

Bearing Holder : No Support, no platform adhesion

Laser Holder Core : No Support, brim or raft suggested

Gear : No Support needed, brim or raft suggested

Note: Orientations do not necessarily match suggested printing orientation.