[profile] layer_height = 0.9 wall_thickness = 2.4 retraction_enable = True solid_layer_thickness = 1.8 fill_density = 20 perimeter_before_infill = True nozzle_size = 1.2 print_speed = 15 print_temperature = 240 print_temperature2 = 0 print_temperature3 = 0 print_temperature4 = 0 print_temperature5 = 0 print_bed_temperature = 110 support = None platform_adhesion = None support_dual_extrusion = Both wipe_tower = False wipe_tower_volume = 15 ooze_shield = False filament_diameter = 2.85 filament_diameter2 = 0 filament_diameter3 = 0 filament_diameter4 = 0 filament_diameter5 = 0 filament_flow = 100.0 retraction_speed = 15 retraction_amount = 3 retraction_dual_amount = 16.5 retraction_min_travel = 1.5 retraction_combing = All retraction_minimal_extrusion = 0.005 retraction_hop = 0.1 bottom_thickness = 0.9 layer0_width_factor = 125 object_sink = 0 overlap_dual = 0.15 travel_speed = 175 bottom_layer_speed = 22 infill_speed = 35 solidarea_speed = 32 inset0_speed = 30 insetx_speed = 32 cool_min_layer_time = 5 fan_enabled = True skirt_line_count = 1 skirt_gap = 3.0 skirt_minimal_length = 250 fan_full_height = 3 fan_speed = 20 fan_speed_max = 30 cool_min_feedrate = 10 cool_head_lift = False solid_top = True solid_bottom = True fill_overlap = 15 support_type = Lines support_angle = 45 support_fill_rate = 30 support_xy_distance = 2.5 support_z_distance = .15 spiralize = False simple_mode = False brim_line_count = 10 raft_margin = 5.0 raft_line_spacing = 5.0 raft_base_thickness = 0.5 raft_base_linewidth = 1.2 raft_interface_thickness = 0.5 raft_interface_linewidth = 1.2 raft_airgap_all = 0.1 raft_airgap = 0.5 raft_surface_layers = 2 raft_surface_thickness = 0.5 raft_surface_linewidth = 1.0 fix_horrible_union_all_type_a = True fix_horrible_union_all_type_b = False fix_horrible_use_open_bits = False fix_horrible_extensive_stitching = False plugin_config = (lp1 . object_center_x = -1 object_center_y = -1 simplemodesettings = simplemodeprofile = 2_normal simplemodematerial = 1_pla simplemodematerialtype = Beginner [alterations] start.gcode = ;This profile is designed specifically for LulzBot TAZ 6 3D Printer ;Basic slice data: ;Sliced at: {day} {date} {time} ;Layer height: {layer_height} ;Walls: {wall_thickness} ;Fill: {fill_density} ;Estimated Print time: {print_time} ;Filament used: {filament_amount}m {filament_weight}g ;Filament cost: {filament_cost} G26 ; clear potential 'probe fail' condition G21 ; set units to Millimetres M107 ; disable fans G90 ; absolute positioning M82 ; set extruder to absolute mode G92 E0 ; set extruder position to 0 M907 E106 ; set appropriate extruder torque M140 S{print_bed_temperature}; get bed heating up G28 XY ; home X and Y G1 X-19 Y258 F1000 ; move to safe homing position M109 S170 ; soften filament for z homing G28 Z ; home Z M104 S175 ; wipe temp G1 E-30 F100 ; suck up XXmm of filament G1 X-15 Y100 F3000 ; move above wiper pad G1 Z1 ; push nozzle into wiper G1 X-17 Y95 F1000 ; slow wipe G1 X-17 Y90 F1000 ; slow wipe G1 X-17 Y85 F1000 ; slow wipe G1 X-15 Y90 F1000 ; slow wipe G1 X-17 Y80 F1000 ; slow wipe G1 X-15 Y95 F1000 ; slow wipe G1 X-17 Y75 F2000 ; fast wipe G1 X-15 Y65 F2000 ; fast wipe G1 X-17 Y70 F2000 ; fast wipe G1 X-15 Y60 F2000 ; fast wipe G1 X-17 Y55 F2000 ; fast wipe G1 X-15 Y50 F2000 ; fast wipe G1 X-17 Y40 F2000 ; fast wipe G1 X-15 Y45 F2000 ; fast wipe G1 X-17 Y35 F2000 ; fast wipe G1 X-15 Y40 F2000 ; fast wipe G1 X-17 Y70 F2000 ; fast wipe G1 X-15 Y30 Z2 F2000 ; fast wipe G1 X-17 Y35 F2000 ; fast wipe G1 X-15 Y25 F2000 ; fast wipe G1 X-17 Y30 F2000 ; fast wipe G1 X-15 Y25 Z1.5 F1000 ; slow wipe G1 X-17 Y23 F1000 ; slow wipe G1 Z10 ; raise extruder M109 S175 ; heat to probe temp G1 X-9 Y-9 ; move above probe M204 S100 ; set accel for probing G29 ; probe sequence (for auto-leveling) M204 S250 ; set accel back to normal G1 X0 Y0 Z15 F5000 ; get out the way M400 ; clear buffer G4 S1 ; pause M117 Heating... ; LCD status message M140 S{print_bed_temperature}; get bed heating up M109 S{print_temperature} ; set extruder temp and wait M190 S{print_bed_temperature}; get bed temping up during first layer G1 Z2 E0 F75 ; extrude filament back into nozzle M117 TAZ Printing... ; LCD status message end.gcode = ; M400 ; wait for moves to finish M104 S0 ; hotend off M107 ; fans off G91 ; relative positioning G1 E-1 F300 ; retract the filament a bit before lifting the nozzle, to release some of the pressure G1 Z+20 E-5 X-20 Y-20 F3000 ; move Z up a bit and retract filament even more M117 Cooling please wait ; progress indicator message G90 ; absolute positioning G1 Y0 F3000 ; move to cooling position M190 S50 ; set bed to cool off G1 Y280 F3000 ; present finished print M84 ; steppers off G90 ; absolute positioning M117 Print complete ; progress indicator message ;{profile_string} start2.gcode = ;Sliced at: {day} {date} {time} ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} ;Print time: {print_time} ;Filament used: {filament_amount}m {filament_weight}g ;Filament cost: {filament_cost} ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line ;M104 S{print_temperature} ;Uncomment to add your own temperature line ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line G21 ;metric values G90 ;absolute positioning M107 ;start with the fan off G28 X0 Y0 ;move X/Y to min endstops G28 Z0 ;move Z to min endstops G1 Z15.0 F{travel_speed} ;move the platform down 15mm T1 ;Switch to the 2nd extruder G92 E0 ;zero the extruded length G1 F200 E10 ;extrude 10mm of feed stock G92 E0 ;zero the extruded length again G1 F200 E-{retraction_dual_amount} T0 ;Switch to the first extruder G92 E0 ;zero the extruded length G1 F200 E10 ;extrude 10mm of feed stock G92 E0 ;zero the extruded length again G1 F{travel_speed} ;Put printing message on LCD screen M117 Printing... end2.gcode = ;End GCode M104 T0 S0 ;extruder heater off M104 T1 S0 ;extruder heater off M140 S0 ;heated bed heater off (if you have it) G91 ;relative positioning G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way M84 ;steppers off G90 ;absolute positioning ;{profile_string} start3.gcode = ;Sliced at: {day} {date} {time} ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} ;Print time: {print_time} ;Filament used: {filament_amount}m {filament_weight}g ;Filament cost: {filament_cost} ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line ;M104 S{print_temperature} ;Uncomment to add your own temperature line ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line G21 ;metric values G90 ;absolute positioning M107 ;start with the fan off G28 X0 Y0 ;move X/Y to min endstops G28 Z0 ;move Z to min endstops G1 Z15.0 F{travel_speed} ;move the platform down 15mm T2 ;Switch to the 2nd extruder G92 E0 ;zero the extruded length G1 F200 E10 ;extrude 10mm of feed stock G92 E0 ;zero the extruded length again G1 F200 E-{retraction_dual_amount} T1 ;Switch to the 2nd extruder G92 E0 ;zero the extruded length G1 F200 E10 ;extrude 10mm of feed stock G92 E0 ;zero the extruded length again G1 F200 E-{retraction_dual_amount} T0 ;Switch to the first extruder G92 E0 ;zero the extruded length G1 F200 E10 ;extrude 10mm of feed stock G92 E0 ;zero the extruded length again G1 F{travel_speed} ;Put printing message on LCD screen M117 Printing... end3.gcode = ;End GCode M104 T0 S0 ;extruder heater off M104 T1 S0 ;extruder heater off M104 T2 S0 ;extruder heater off M140 S0 ;heated bed heater off (if you have it) G91 ;relative positioning G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way M84 ;steppers off G90 ;absolute positioning ;{profile_string} start4.gcode = ;Sliced at: {day} {date} {time} ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} ;Print time: {print_time} ;Filament used: {filament_amount}m {filament_weight}g ;Filament cost: {filament_cost} ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line ;M104 S{print_temperature} ;Uncomment to add your own temperature line ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line G21 ;metric values G90 ;absolute positioning M107 ;start with the fan off G28 X0 Y0 ;move X/Y to min endstops G28 Z0 ;move Z to min endstops G1 Z15.0 F{travel_speed} ;move the platform down 15mm T3 ;Switch to the 4th extruder G92 E0 ;zero the extruded length G1 F200 E10 ;extrude 10mm of feed stock G92 E0 ;zero the extruded length again G1 F200 E-{retraction_dual_amount} T2 ;Switch to the 3th extruder G92 E0 ;zero the extruded length G1 F200 E10 ;extrude 10mm of feed stock G92 E0 ;zero the extruded length again G1 F200 E-{retraction_dual_amount} T1 ;Switch to the 2nd extruder G92 E0 ;zero the extruded length G1 F200 E10 ;extrude 10mm of feed stock G92 E0 ;zero the extruded length again G1 F200 E-{retraction_dual_amount} T0 ;Switch to the first extruder G92 E0 ;zero the extruded length G1 F200 E10 ;extrude 10mm of feed stock G92 E0 ;zero the extruded length again G1 F{travel_speed} ;Put printing message on LCD screen M117 Printing... end4.gcode = ;End GCode M104 T0 S0 ;extruder heater off M104 T1 S0 ;extruder heater off M104 T2 S0 ;extruder heater off M104 T3 S0 ;extruder heater off M140 S0 ;heated bed heater off (if you have it) G91 ;relative positioning G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way M84 ;steppers off G90 ;absolute positioning ;{profile_string} support_start.gcode = support_end.gcode = cool_start.gcode = cool_end.gcode = replace.csv = preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders. ;This code is added before the T(n) postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders. ;This code is added after the T(n)