[profile] layer_height = 0.25 wall_thickness = 1.0 retraction_enable = True solid_layer_thickness = 1 fill_density = 20 perimeter_before_infill = True nozzle_size = 0.5 print_speed = 50 print_temperature = 245 print_temperature2 = 0 print_temperature3 = 0 print_temperature4 = 0 print_temperature5 = 0 print_bed_temperature = 75 support = None platform_adhesion = None support_dual_extrusion = Both wipe_tower = False wipe_tower_volume = 15 ooze_shield = False filament_diameter = 2.85 filament_diameter2 = 0 filament_diameter3 = 0 filament_diameter4 = 0 filament_diameter5 = 0 filament_flow = 100.0 retraction_speed = 25 retraction_amount = 4 retraction_dual_amount = 16.5 retraction_min_travel = 1 retraction_combing = All retraction_minimal_extrusion = 0.005 retraction_hop = 0.1 bottom_thickness = 0.425 layer0_width_factor = 125 object_sink = 0.0 overlap_dual = 0.15 travel_speed = 175 bottom_layer_speed = 20 infill_speed = 20 solidarea_speed = 20 inset0_speed = 20 insetx_speed = 20 cool_min_layer_time = 5 fan_enabled = True skirt_line_count = 1 skirt_gap = 3.0 skirt_minimal_length = 250 fan_full_height = 0.5 fan_speed = 100 fan_speed_max = 100 cool_min_feedrate = 10 cool_head_lift = False solid_top = True solid_bottom = True fill_overlap = 15 support_type = Lines support_angle = 45 support_fill_rate = 20 support_xy_distance = 1.5 support_z_distance = 0.15 spiralize = False simple_mode = False brim_line_count = 10 raft_margin = 5.0 raft_line_spacing = 3.0 raft_base_thickness = 0.3 raft_base_linewidth = 1.0 raft_interface_thickness = 0.27 raft_interface_linewidth = 0.4 raft_airgap_all = 0.0 raft_airgap = 0.5 raft_surface_layers = 2 raft_surface_thickness = 0.27 raft_surface_linewidth = 0.4 fix_horrible_union_all_type_a = True fix_horrible_union_all_type_b = False fix_horrible_use_open_bits = False fix_horrible_extensive_stitching = False plugin_config = (lp1 . object_center_x = -1 object_center_y = -1 simplemodesettings = simplemodeprofile = Standard simplemodematerial = PLA simplemodematerialtype = Beginner [alterations] start.gcode = ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} ;Print time: {print_time} ;Filament used: {filament_amount}m {filament_weight}g ;Filament cost: {filament_cost} ;M190 R{print_bed_temperature} ;Uncomment to add your own bed temperature line ;M109 R{print_temperature} ;Uncomment to add your own temperature line G26 ; clear potential 'probe fail' condition G21 ; metric values G90 ; absolute positioning M82 ; set extruder to absolute mode M107 ; start with the fan off G92 E0 ; set extruder position to 0 M140 S{print_bed_temperature}; get bed heating up G28 ; home all M109 R150 ; set to cleaning temp and wait G1 Z150 E-30 F75 ; suck up XXmm of filament M109 R170 ; heat up rest of way G1 X45 Y174 F11520 ; move behind scraper G1 Z0 F1200 ; CRITICAL: set Z to height of top of scraper G1 X45 Y174 Z-.5 F4000 ; wiping ; plunge into wipe pad G1 X55 Y172 Z-.5 F4000 ; wiping G1 X45 Y174 Z0 F4000 ; wiping G1 X55 Y172 F4000 ; wiping G1 X45 Y174 F4000 ; wiping G1 X55 Y172 F4000 ; wiping G1 X45 Y174 F4000 ; wiping G1 X55 Y172 F4000 ; wiping G1 X60 Y174 F4000 ; wiping G1 X80 Y172 F4000 ; wiping G1 X60 Y174 F4000 ; wiping G1 X80 Y172 F4000 ; wiping G1 X60 Y174 F4000 ; wiping G1 X90 Y172 F4000 ; wiping G1 X80 Y174 F4000 ; wiping G1 X100 Y172 F4000 ; wiping G1 X80 Y174 F4000 ; wiping G1 X100 Y172 F4000 ; wiping G1 X80 Y174 F4000 ; wiping G1 X100 Y172 F4000 ; wiping G1 X110 Y174 F4000 ; wiping G1 X100 Y172 F4000 ; wiping G1 X110 Y174 F4000 ; wiping G1 X100 Y172 F4000 ; wiping G1 X110 Y174 F4000 ; wiping G1 X115 Y172 Z-0.5 F1000 ; wipe slower and bury noz in cleanish area G1 Z10 ; raise z G28 X0 Y0 ; home x and y M109 R170 ; set to probing temp M204 S300 ; set accel for probing G29 ; Probe M204 S2000 ; set accel back to normal G1 X5 Y15 Z10 F5000 ; get out the way M400 ; clear buffer G4 S1 ; pause M109 R{print_temperature} ; set extruder temp and wait G4 S25 ; wait for bed to temp up G1 Z2 E0 F75 ; extrude filament back into nozzle M140 S{print_bed_temperature}; get bed temping up during first layer end.gcode = M400 M104 S0 ; hotend off M140 S0 ; heated bed heater off (if you have it) M107 ; fans off G92 E5 ; set extruder to 5mm for retract on print end G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning M190 R50 ; wait for bed to cool M140 S0 ; G1 X145 F1000 ; move to cooling positioning G1 Y175 F1000 ; move to cooling positioning M84 ; steppers off G90 ; absolute positioning ;{profile_string} start2.gcode = ;Sliced at: {day} {date} {time} ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} ;Print time: {print_time} ;Filament used: {filament_amount}m {filament_weight}g ;Filament cost: {filament_cost} ;M190 R{print_bed_temperature} ;Uncomment to add your own bed temperature line ;M104 S{print_temperature} ;Uncomment to add your own temperature line ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line G21 ;metric values G90 ;absolute positioning M107 ;start with the fan off G28 X0 Y0 ;move X/Y to min endstops G28 Z0 ;move Z to min endstops G1 Z15.0 F{travel_speed} ;move the platform down 15mm T1 ;Switch to the 2nd extruder G92 E0 ;zero the extruded length G1 F200 E10 ;extrude 10mm of feed stock G92 E0 ;zero the extruded length again G1 F200 E-{retraction_dual_amount} T0 ;Switch to the first extruder G92 E0 ;zero the extruded length G1 F200 E10 ;extrude 10mm of feed stock G92 E0 ;zero the extruded length again G1 F{travel_speed} ;Put printing message on LCD screen M117 Printing... end2.gcode = ;End GCode M104 T0 S0 ;extruder heater off M104 T1 S0 ;extruder heater off M140 S0 ;heated bed heater off (if you have it) G91 ;relative positioning G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way M84 ;steppers off G90 ;absolute positioning ;{profile_string} start3.gcode = ;Sliced at: {day} {date} {time} ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} ;Print time: {print_time} ;Filament used: {filament_amount}m {filament_weight}g ;Filament cost: {filament_cost} ;M190 R{print_bed_temperature} ;Uncomment to add your own bed temperature line ;M104 S{print_temperature} ;Uncomment to add your own temperature line ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line G21 ;metric values G90 ;absolute positioning M107 ;start with the fan off G28 X0 Y0 ;move X/Y to min endstops G28 Z0 ;move Z to min endstops G1 Z15.0 F{travel_speed} ;move the platform down 15mm T2 ;Switch to the 2nd extruder G92 E0 ;zero the extruded length G1 F200 E10 ;extrude 10mm of feed stock G92 E0 ;zero the extruded length again G1 F200 E-{retraction_dual_amount} T1 ;Switch to the 2nd extruder G92 E0 ;zero the extruded length G1 F200 E10 ;extrude 10mm of feed stock G92 E0 ;zero the extruded length again G1 F200 E-{retraction_dual_amount} T0 ;Switch to the first extruder G92 E0 ;zero the extruded length G1 F200 E10 ;extrude 10mm of feed stock G92 E0 ;zero the extruded length again G1 F{travel_speed} ;Put printing message on LCD screen M117 Printing... end3.gcode = ;End GCode M104 T0 S0 ;extruder heater off M104 T1 S0 ;extruder heater off M104 T2 S0 ;extruder heater off M140 S0 ;heated bed heater off (if you have it) G91 ;relative positioning G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way M84 ;steppers off G90 ;absolute positioning ;{profile_string} start4.gcode = ;Sliced at: {day} {date} {time} ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} ;Print time: {print_time} ;Filament used: {filament_amount}m {filament_weight}g ;Filament cost: {filament_cost} ;M190 R{print_bed_temperature} ;Uncomment to add your own bed temperature line ;M104 S{print_temperature} ;Uncomment to add your own temperature line ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line G21 ;metric values G90 ;absolute positioning M107 ;start with the fan off G28 X0 Y0 ;move X/Y to min endstops G28 Z0 ;move Z to min endstops G1 Z15.0 F{travel_speed} ;move the platform down 15mm T3 ;Switch to the 4th extruder G92 E0 ;zero the extruded length G1 F200 E10 ;extrude 10mm of feed stock G92 E0 ;zero the extruded length again G1 F200 E-{retraction_dual_amount} T2 ;Switch to the 3th extruder G92 E0 ;zero the extruded length G1 F200 E10 ;extrude 10mm of feed stock G92 E0 ;zero the extruded length again G1 F200 E-{retraction_dual_amount} T1 ;Switch to the 2nd extruder G92 E0 ;zero the extruded length G1 F200 E10 ;extrude 10mm of feed stock G92 E0 ;zero the extruded length again G1 F200 E-{retraction_dual_amount} T0 ;Switch to the first extruder G92 E0 ;zero the extruded length G1 F200 E10 ;extrude 10mm of feed stock G92 E0 ;zero the extruded length again G1 F{travel_speed} ;Put printing message on LCD screen M117 Printing... end4.gcode = ;End GCode M104 T0 S0 ;extruder heater off M104 T1 S0 ;extruder heater off M104 T2 S0 ;extruder heater off M104 T3 S0 ;extruder heater off M140 S0 ;heated bed heater off (if you have it) G91 ;relative positioning G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way M84 ;steppers off G90 ;absolute positioning ;{profile_string} support_start.gcode = support_end.gcode = cool_start.gcode = cool_end.gcode = replace.csv = preswitchextruder.gcode = ;Switch between the current extruder and the next ex postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders. ;This code is added after the T(n)